Tektelic KONA 16 Macro

Prerequisite

Verify Tektelic's default packet forwarder is not running

ps -eadf |grep -i pkt

If Tektelic's default packet forwarder is found to be running you will see a pkt_forwarder process running as shown in the example below.

If you do not see any processes running skip to the installation steps below.

#ps -eadf |grep -i pkt
root      2429     1  0 17:14 ?        00:00:37 /usr/bin/pkt_forwarder -c /etc/default/config.json -s
root     23729 23692  0 18:19 pts/0    00:00:00 grep -i pkt

Confirm the running forwarder is Tektelic's packet forwarder

opkg list-installed |grep pkt

If the installed forwarder running is Tectelic you will see kona-pkt-forwarder listed in the output.

#opkg list-installed |grep pkt
kona-pkt-forwarder - 4.0.17-r110
kona-pkt-forwarder-config - 4.0.17-r110
kona-pkt-forwarder-dvt-utils - 4.0.17-r110
kona-pkt-forwarder-utils - 4.0.17-r110

Remove the Tektelic packet forwarder

If the installed packet forwarder was confirmed to be Tektelic, remove the forwarder with the following command.

opkg remove kona-pkt-forwarder

Example output.

Removing package kona-pkt-forwarder from root...
Stopping Tektelic Packet Forwarder: Reinitializing monit daemon
 Removing any system startup links for pkt_fwd ...
  /etc/rc0.d/K10pkt_fwd
  /etc/rc1.d/K10pkt_fwd
  /etc/rc2.d/K10pkt_fwd
  /etc/rc3.d/K10pkt_fwd
  /etc/rc4.d/K10pkt_fwd
  /etc/rc5.d/S99pkt_fwd
  /etc/rc6.d/K10pkt_fwd

Verify the default packet forwarder is no longer running

ps -eadf |grep -i pkt

There should no longer be any running packet forwarder processes found.

root     11002 23692  0 19:20 pts/0    00:00:00 grep -i pkt

SenRa Packet Forwarder for Developers

Registration

If you have not done so already you will need to register your gateway through your Developer or RAN Provider account.

Note

The serial number for this device is the 8 digit Product Type (starting with a "T") an underscore "_" followed by the 9 digit serial number which can be found on bottom of the Gateway.

Installation

Copy and paste the following command into the Tektelic KONA 16 Macro SSH console.

BSP Version Command
BSP: 4.0.X
dlF=lgwInstaller_02_14_12.sh;dlC=senraco;wget --no-check-certificate http://docs.${dlC}.io/downloads/02_14_12/$dlF -O $dlF && chmod +x $dlF && ./${dlF} -c ${dlC} -t DEV

Run the command. The installation is automatic and will prompt you once it has completed.

reboot

Once registration and Gateway software installation are complete the Gateway will be displayed in the SenRa Portal Dashboard with the current registration status (this may require a refresh of the browser).

SenRa Packet Forwarder for RAN Providers

Note

Before installing verify you have properly configured your network settings on the gateway. The installation process will apply security measures which include modifications to the firewall as well as the password; the installer may also configure the system and install new packages. Access to the gateway over the local network through such protocols as SSH and telnet will no longer be available upon completion of the installer.

Registration

If you have not done so already you will need to register your gateway through your Developer or RAN Provider account.

Note

The serial number for this device is the 8 digit Product Type (starting with a "T") an underscore "_" followed by the 9 digit serial number which can be found on bottom of the Gateway.

Installation

Copy and paste the following command into the Tektelic KONA 16 Macro SSH console.

BSP Version Command
BSP: 4.0.X
dlF=lgwInstaller_02_14_12.sh;dlC=senraco;wget --no-check-certificate http://docs.${dlC}.io/downloads/02_14_12/$dlF -O $dlF && chmod +x $dlF && ./${dlF} -c ${dlC} -t RAN

Run the command. The installation is automatic and will prompt you once it has completed.

reboot

Once registration and Gateway software installation are complete the Gateway will be displayed in the SenRa Portal Dashboard with the current registration status (this may require a refresh of the browser).